View CY3686_1726774.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ez-usb nx2lp-flex? flexible usb nand flash controller cy7c68033/cy7c68034 cypress semiconductor corporation ? 198 champion court ? san jose , ca 95134-1709 ? 408-943-2600 document #: 001-04247 rev. *d revised september 21, 2006 cy7c68033/cy7c68034 silicon features ? certified compliant for bus- or self-powered usb 2.0 operation (tid# 40490118) ? single-chip, integrated usb 2.0 transceiver and smart sie ? ultra low power ? 43 ma typical current draw in any mode ? enhanced 8051 core ? firmware runs from internal ram, which is downloaded from nand flash at startup ? no external eeprom required ? 15 kbytes of on-chip code/data ram ? default nand firmware ~8 kb ? default free space ~7 kb ? four programmable bulk /interrupt/isochronous endpoints ? buffering options: double, triple, and quad ? additional programmable (bulk/interrupt) 64-byte endpoint ? smartmedia standard hardware ecc generation with 1-bit correction and 2-bit detection ? gpif (general programmable interface) ? allows direct connection to most parallel interfaces ? programmable waveform descriptors and configuration registers to define waveforms ? supports multiple ready (rdy) inputs and control (ctl) outputs ? 12 fully-programmable gpio pins ? integrated, industry-standard enhanced 8051 ? 48-mhz, 24-mhz, or 12-mhz cpu operation ? four clocks per instruction cycle ? three counter/timers ? expanded interrupt system ? two data pointers ? 3.3v operation with 5v tolerant inputs ? vectored usb interrupts and gpif/fifo interrupts ? separate data buffers for the se t-up and data portions of a control transfer ? integrated i 2 c? controller, runs at 100 or 400 khz ? four integrated fifos ? integrated glue logic and fifos lower system cost ? automatic conversion to and from 16-bit buses ? master or slave operation ? uses external clock or asynchronous strobes ? easy interface to asic and dsp ics ? available in space saving, 56-pin qfn package cy7c68034 only silicon features: ? ideal for battery powered applications ? suspend current: 100 a (typ.) cy7c68033 only silicon features: ? ideal for non-battery powered applications ? suspend current: 300 a (typ.) x20 pll /0.5 /1.0 /2.0 8051 core 12/24/48 mhz, four clocks/cycle v cc 1.5k d+ d? address (16)/data bus (8) gpif cy smart usb 1.1/2.0 engine usb 2.0 xcvr additional i/os ctl (3) rdy (2) 8/16 ecc nand boot logic (rom) nx2lp-flex 24 mhz ext. xtal connected for full-speed usb integrated full- and high-speed xcvr 15 kb ram general programmable i/f to asic/dsp or bus standards such as 8-bit nand, epp, etc. 4 kb fifo up to 96 mb/s burst rate high-performance, enhanced 8051 core with low power options ?soft configuration? enables easy firmware changes fifo and usb endpoint memory (master or slave modes) enhanced usb core simplifies 8051 code i 2 c master block diagram [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 2 of 33 default nand firmware features because the nx2lp-flex? is intended for nand flash-based usb mass storage applications, a default firmware image is included in the development kit with the following features: ? high (480-mbps) or full (12-mbps) speed usb support ? both common nand page sizes supported ? 512 bytes for up to 1 gb capacity ? 2k bytes for up to 8 gb capacity ? 12 configurable general-purpose i/o (gpio) pins ? 2 dedicated chip enable (ce#) pins ? 6 configurable ce#/gpio pins ? up to 8 nand flash single-device (single-die) chips are supported ? up to 4 nand flash dual-device (dual-die) chips are supported ? compile option allows unused ce# pins to be config- ured as gpios ? 4 dedicated gpio pins ? industry standard ecc nand flash correction ? 1-bit per 256-bit correction ? 2-bit error detection ? industry standard (smartmedia) page management for wear leveling algorithm, bad block handling, and physical to logical management. ? 8-bit nand flash interface support ? support for 30-ns, 50-ns, and 100-ns nand flash timing ? complies with the usb mass storage class specification revision 1.0 the default firmware image implements a usb 2.0 nand flash controller. this controller adheres to the mass storage class bulk-only transport specification . the usb port of the nx2lp-flex is connected to a host computer directly or via the downstream port of a usb hub. host software issues commands and data to the nx2lp-flex and receives status and data from the nx2lp-flex using standard usb protocol. the default firmware image supports industry leading 8-bit nand flash interfaces and both common nand page sizes of 512 and 2k bytes. up to eight chip enable pins allow the nx2lp-flex to be connected to up to eight single- or four dual-die nand flash chips. complete source code and documentation for the default firmware image are included in the nx2lp-flex development kit to enable customization for meeting design requirements. additionally, compile options for the default firmware allow for quick configuration of some features to decrease design effort and increase time-to-market advantages. overview cypress semiconductor corporation?s (cypress?s) ez-usb nx2lp-flex (cy7c68033/cy7c68034) is a firmware-based, programmable version of the ez-usb nx2lp ? (cy7c68023/cy7c68024), which is a fixed-function, low-power usb 2.0 nand flash controller. by integrating the usb 2.0 transceiver, serial interface engine (sie), enhanced 8051 microcontroller, and a programmable peripheral interface in a single chip, cypress has created a very cost-effective solution that enables feature-rich nand flash-based applications. the ingenious architecture of nx2lp-flex results in usb data transfer rates of over 53 mbytes per second, the maximum-allowable usb 2.0 bandwidth, while still using a low-cost 8051 microcontroller in a small 56-pin qfn package. because it incorporates the usb 2.0 transceiver, the nx2lp-flex is more economical, providing a smaller footprint solution than external usb 2. 0 sie or transceiver implemen- tations. with ez-usb nx2lp- flex, the cypress smart sie handles most of the usb 1.1 and 2.0 protocol, freeing the embedded microcontroller for app lication-specific functions and decreasing development time while ensuring usb compatibility. the general programmable interface (gpif) and master/slave endpoint fifo (8 - or 16-bit data bus) provide an easy and glueless interface to popular interfaces such as utopia, epp, i 2 c, pcmcia, and most dsp processors. applications the nx2lp-flex allows designers to add extra functionality to basic nand flash mass storage designs, or to interface them with other peripheral devices. applications may include: ? nand flash-based gps devices ? nand flash-based dvb video capture devices ? wireless pointer/presenter t ools with nand flash storage ? nand flash-based mpeg/tv conversion devices ? legacy conversion devices with nand flash storage ? nand flash-based cameras ? nand flash mass storage device with biometric (e.g., fingerprint) security ? home pna devices with nand flash storage ? wireless lan with nand flash storage ? nand flash-based mp3 players ? lan networking with nand flash storage [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 3 of 33 figure 1. example dvb block diagram figure 2. example gps block diagram the ?reference designs? section of the cypress web site provides additional tools for typical usb 2.0 applications. each reference design comes complete with firmware source and object code, schematics, and documentation. please visit http://www.cypress.com for more information. functional overview usb signaling speed nx2lp-flex operates at two of the three rates defined in the usb specification revision 2.0, dated april 27, 2000: ? full speed, with a signaling bit rate of 12 mbps ? high speed, with a signaling bit rate of 480 mbps. nx2lp-flex does not support the low-speed signaling mode of 1.5 mbps. 8051 microprocessor the 8051 microprocessor embedded in the nx2lp-flex has 256 bytes of register ram, an expanded interrupt system and three timer/counters. 8051 clock frequency nx2lp-flex has an on-chip oscillator circuit that uses an external 24-mhz (100-ppm) crystal with the following charac- teristics: ? parallel resonant ? fundamental mode ? 500- w drive level ? 12-pf (5% tolerance) load capacitors. an on-chip pll multiplies the 24-mhz oscillator up to 480 mhz, as required by the transceiver/phy, and internal counters divide it down for use as the 8051 clock. the default 8051 clock frequency is 12 mhz. the clock frequency of the 8051 can be changed by the 8051 through the cpucs register, dynamically figure 3. crystal configuration. special function registers certain 8051 sfr addresses are populated to provide fast access to critical nx2lp-flex functions. these sfr additions are shown in ta ble 1 . bold type indicates non-standard, enhanced 8051 registers. the two sfr rows that end with ?0? and ?8? contain bit-addressable registers. the four i/o ports a?d use the sfr addresses used in the standard 8051 for ports 0?3, which are not implemented in nx2lp-flex. because of the faster and more efficient sfr addressing, the nx2lp-flex i/o ports are not addressable in external ram space (using the movx instruction). i 2 c bus nx2lp supports the i 2 c bus as a master only at 100-/400-khz. scl and sda pins have open-drain outputs and hysteresis inputs. these signals must be pulled up to 3.3v, even if no i 2 c device is connected. the i 2 c bus is disabled at startup and only available for use after the initial nand access. lcd nx2lp- flex buttons dvb decoder nand bank(s) ce[7:0] ctl i/o i/o d+/- i/o i/o nand-based dvb unit audio / video i/o nx2lp- flex buttons gps nand bank(s) ce[7:0] ctl i/o d+/- i/o i/o nand-based gps unit lcd i/o 12 pf 12 pf 24 mhz 20 pll c1 c2 12-pf capacitor values assumes a trace capacitance of 3 pf per side on a four-layer fr4 pca [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 4 of 33 buses the nx2lp-flex features an 8- or 16-bit ?fifo? bidirectional data bus, multiplexed on i/o ports b and d. the default firmware image implements an 8-bit data bus in gpif master mode. it is recommended that additional inter- faces added to the default firmware image use this 8-bit data bus. enumeration during the start-up sequence, internal logic checks for the presence of nand flash with valid firmware. if valid firmware is found, the nx2lp-flex loads it and operates according to the firmware. if no nand flash is detected, or if no valid firmware is found, the nx2lp-flex uses the default values from internal rom space for manufacturing mode operation. the two modes of operation ar e described in the section ?normal operation mode? on page 5 and ?manufacturing mode? on page 5. table 1. special function registers x8x 9x ax bx cxdxexfx 0 ioa iob ioc iod scon1 psw acc b 1sp exif int2clr ioe sbuf1 2dpl0 mpage int4clr oea 3dph0 oeb 4 dpl1 oec 5 dph1 oed 6 dps oee 7pcon 8 tcon scon0 ie ip t2con eicon eie eip 9 tmod sbuf0 atl0 autoptrh1 ep2468stat ep01stat rcap2l btl1 autoptrl1 ep24fifoflgs gpiftrig rcap2h cth0 reserved ep68fifoflgs tl2 dth1 autoptrh2 gpifsgldath th2 e ckcon autoptrl2 gpifsgldatlx f reserved autoptrset-up gpifsgldatlnox [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 5 of 33 figure 4. nx2lp-flex enumeration sequence normal operation mode in normal operation mode, th e nx2lp-flex behaves as a usb 2.0 mass storage class nand flash controller. this includes all typical usb device states (powered, configured, etc.). the usb descriptors are returned according to the data stored in the configuration data memory area. normal read and write access to the nand flash is available in this mode. manufacturing mode in manufacturing mode, the nx2lp-flex enumerates using the default descriptors and conf iguration data that are stored in internal rom space. this mode allows for first-time programming of the configuration data memory area, as well as board-level manufacturing tests. default silicon id values to facilitate proper usb enumeration when no programmed nand flash is present, the nx2l p-flex has default silicon id values stored in rom space. the default silicon id values should only be used for development purposes. cypress requires designers to use their own vendor id for final products. a vendor id is obtained through registration with the usb implementor?s forum (usb-i f). also, if the nx2lp-flex is used as a mass storage class device, a unique usb serial number is required for each device in order to comply with the usb mass storage class specification. cypress provides all the software tools and drivers necessary for properly programming and testing the nx2lp-flex. please refer to the documentation in the development kit for more information on these topics. renumeration? cypress?s renumeration? feature is used in conjunction with the nx2lp-flex manufacturing software tools to enable first-time nand programming. it is only available when used in conjunction with the nx2lp-flex manufacturing tools, and is not enabled during normal operation. bus-powered applications the nx2lp-flex fully supports bus-powered designs by enumerating with less than 100 ma, as required by the usb 2.0 specification. interrupt system int2 interrupt request and enable registers nx2lp-flex implements an autovector feature for int2 and int4. there are 27 int2 (usb) vectors, and 14 int4 (fifo/gpif) vectors. see th e ez-usb technical reference manual (trm) for more details. usb-interrupt autovectors the main usb interrupt is shared by 27 interrupt sources. to save the code and processing ti me that normally would be required to identify the individual usb interrupt source, the nx2lp-flex provides a second level of interrupt vectoring, called autovectoring. when a usb interrupt is asserted, the nx2lp-flex pushes the program counter onto its stack then jumps to address 0x0500, where it expects to find a ?jump? instruction to the usb interrupt service routine. developers familiar with cypress?s programmable usb devices should note that these interrupt vector values differ from those used in other ez-u sb microcontrollers. this is due to the additional nand boot logic that is present in the nx2lp-flex rom space. also, these values are fixed and cannot be changed in the firmware. nand flash programmed? load default descriptors and configuration data manufacturing mode load firmware from nand enumerate according to firmware normal operation mode start-up enumerate as unprogrammed nx2lp-flex nand flash present? no yes yes no table 2. default silicon id values default vid/pid/did vendor id 0x04b4 cypress semiconductor product id 0x8613 ez-usb ? default device release 0xannn depends on chip revision (nnn = chip revision, where first silicon = 001) [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 6 of 33 if autovectoring is enabled (av2en = 1 in the intset-up register), the nx2lp-flex su bstitutes its int2vec byte. therefore, if the high byte (?page?) of a jump-table address is preloaded at location 0x544, the automatically-inserted int2vec byte at 0x545 will direct the jump to the correct address out of the 27 addresses within the page. fifo/gpif interrupt (int4) just as the usb interrupt is shared among 27 individual usb-interrupt sources, the fi fo/gpif interrupt is shared among 14 individual fifo/gpif sources. the fifo/gpif interrupt, like the usb interrupt, can employ autovectoring. table 4 shows the priority and int4vec values for the 14 fifo/gpif interrupt sources. table 3. int2 usb interrupts usb interrupt table for int2 priority int2vec value source notes 1 0x500 sudav setup data available 2 0x504 sof start of frame (or microframe) 3 0x508 sutok setup token received 4 0x50c suspend usb suspend request 5 0x510 usb reset bus reset 6 0x514 hispeed entered high speed operation 7 0x518 ep0ack nx2lp ack?d the control handshake 8 0x51c reserved 9 0x520 ep0-in ep0-in ready to be loaded with data 10 0x524 ep0-out ep0-out has usb data 11 0x528 ep1-in ep1-in ready to be loaded with data 12 0x52c ep1-out ep1-out has usb data 13 0x530 ep2 in: buffer available. out: buffer has data 14 0x534 ep4 in: buffer available. out: buffer has data 15 0x538 ep6 in: buffer available. out: buffer has data 16 0x53c ep8 in: buffer available. out: buffer has data 17 0x540 ibn in-bulk-nak (any in endpoint) 18 0x544 reserved 19 0x548 ep0ping ep0 out was pinged and it nak?d 20 0x54c ep1ping ep1 out wa s pinged and it nak?d 21 0x550 ep2ping ep2 out was pinged and it nak?d 22 0x554 ep4ping ep4 out was pinged and it nak?d 23 0x558 ep6ping ep6 out was pinged and it nak?d 24 0x55c ep8ping ep8 out wa s pinged and it nak?d 25 0x560 errlimit bus errors exceeded the programmed limit 26 0x564 reserved 27 0x568 reserved 28 0x56c reserved 29 0x570 ep2isoerr iso ep2 out pid sequence error 30 0x574 ep4isoerr iso ep4 out pid sequence error 31 0x578 ep6isoerr iso ep6 out pid sequence error 32 0x57c ep8isoerr iso ep8 out pid sequence error [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 7 of 33 if autovectoring is enabled (av4en = 1 in the intset-up register), the nx2lp-flex su bstitutes its int4vec byte. therefore, if the high byte (?page?) of a jump-table address is preloaded at location 0x554, the automatically-inserted int4vec byte at 0x555 will direct the jump to the correct address out of the 14 addresses within the page. when the isr occurs, the nx2lp-flex pushes the program counter onto its stack then jumps to address 0x553, where it expects to find a ?jump? instruction to the is r interrupt service routine. reset and wakeup reset pin the input pin reset#, will reset the nx2lp-flex when asserted. this pin has hysteresis and is active low. when a crystal is used as the clock source for the nx2lp-flex, the reset period must allow for the stabilization of the crystal and the pll. this reset period should be approximately 5 ms after v cc has reached 3.0v. if the crystal input pin is driven by a clock signal, the internal pll stabilizes in 200 s after v cc has reached 3.0v [1] . figure 5 shows a power-on reset condition and a reset applied during operation. a power-on reset is defined as the time reset is asserted while power is being applied to the circuit. a powered reset is defined to be when the nx2lp-flex has previously been powered on and operating and the reset# pin is asserted. cypress provides an application note which describes and recommends power on reset implementation and can be found on the cypress web site. for mo re information on reset imple- mentation for the ez-usb family of products visit the http://www.cypress.com website. table 4. individual fifo/gpif interrupt sources priority int4vec value source notes 1 0x580 ep2pf endpoint 2 programmable flag 2 0x584 ep4pf endpoint 4 programmable flag 3 0x588 ep6pf endpoint 6 programmable flag 4 0x58c ep8pf endpoint 8 programmable flag 5 0x590 ep2ef endpoint 2 empty flag 6 0x594 ep4ef endpoint 4 empty flag 7 0x598 ep6ef endpoint 6 empty flag 8 0x59c ep8ef endpoint 8 empty flag 9 0x5a0 ep2ff endpoint 2 full flag 10 0x5a4 ep4ff endpoint 4 full flag 11 0x5a8 ep6ff endpoint 6 full flag 12 0x5ac ep8ff endpoint 8 full flag 13 0x5b0 gpifdone gpif operation complete 14 0x5b4 gpifwf gpif waveform note 1. if the external clock is powered at the same time as the cy7c68033/cy7c68034 and has a stabilization wait period, it must be added to the 200 s. figure 5. reset timing plots v il 0v 3.3v 3.0v t reset v cc reset# power-on reset t reset v cc reset# v il powered reset 3.3v 0v [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 8 of 33 wakeup pins the 8051 puts itself and the rest of the chip into a power-down mode by setting pcon.0 = 1. this stops the oscillator and pll. when wakeup is asserted by external logic, the oscil- lator restarts, after the pll stabilizes, and then the 8051 receives a wakeup interrupt. this applies whether or not nx2lp-flex is connected to the usb. the nx2lp-flex exits the power-down (usb suspend) state using one of the following methods: ? usb bus activity (if d+/d? lines are left floating, noise on these lines may indicate activity to the nx2lp-flex and initiate a wakeup). ? external logic asserts the wakeup pin ? external logic asserts the pa3/wu2 pin. the second wakeup pin, wu2, can also be configured as a general purpose i/o pin. this allows a simple external r-c network to be used as a periodic wakeup source. note that wakeup is, by default, active low. program/data ram internal rom/ram size the nx2lp-flex has 1 kbytes rom and 15 kbytes of internal program/data ram, where psen# /rd# signals are internally ored to allow the 8051 to access it as both program and data memory. no usb control registers appear in this space. internal code memory this mode implements the internal block of ram (starting at 0x0500) as combined code and data memory, as shown in figure 6 , below. only the internal and scratch pad ram spaces have the following access: ? usb download (only supported by the cypress manufac- turing tool) ? setup data pointer ? nand boot access. figure 6. internal code memory register addresses figure 7. internal register addresses table 5. reset timing values condition t reset power-on reset with crystal 5 ms power-on reset with external clock source 200 s + clock stability time powered reset 200 s *sudptr, usb download, nand boot access ffff e200 e1ff e000 3fff 0000 7.5 kbytes usb registers and 4 kbytes fifo buffers (rd#, wr#) 512 bytes ram data (rd#, wr#)* 15 kbytes ram code and data (psen#, rd#, wr#)* 0500 1 kbyte rom ffff e800 e7bf e740 e73f e700 e6ff e500 e4ff e480 e47f e400 e200 e1ff e000 e3ff efff 2 kbytes reserved 64 bytes ep0 in/out 64 bytes reserved 8051 addressable registers reserved (128) 128 bytes gpif waveforms 512 bytes 8051 xdata ram f000 (512) reserved (512) e780 64 bytes ep1out e77f 64 bytes ep1in e7ff e7c0 4 kbytes ep2-ep8 buffers (8 x 512) [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 9 of 33 endpoint ram size ? 3 64 bytes (endpoints 0 and 1) ? 8 512 bytes (endpoints 2, 4, 6, 8) organization ? ep0 ? bidirectional endpoint zero, 64-byte buffer ? ep1in, ep1out ? 64-byte buffers, bulk or interrupt ? ep2,4,6,8 ? eight 512-byte buffers, bulk, interrupt, or isochronous. ? ep4 and ep8 can be double buffered, while ep2 and 6 can be either double, triple, or quad buffered. for high-speed endpoint configuration options, see figure 8 . setup data buffer a separate 8-byte buffer at 0xe6b8-0xe6bf holds the setup data from a control transfer. endpoint configurations (high-speed mode) endpoints 0 and 1 are the same for every configuration. endpoint 0 is the only control endpoint, and endpoint 1 can be either bulk or interrupt. the endpoint buffers can be configured in any 1 of the 12 configurations shown in the vertical columns. when operating in full-speed bulk mode, only the first 64 bytes of each buffer are used. for example, in high-speed the max packet size is 512 bytes, but in full-speed it is 64 bytes. even though a buffer is configured to be a 512 byte buffer, in full-speed only the first 64 bytes are used. the unused endpoint buffer space is not available for other opera- tions. an example endpoint configuration would be: ep2?1024 double buffered; ep6?512 quad buffered (column 8 in figure 8 ). figure 8. endpoint configuration default full-speed alternate settings 64 64 64 512 512 1024 1024 1024 1024 1024 1024 1024 512 512 512 512 512 512 512 512 512 512 ep2 ep2 ep2 ep6 ep6 ep8 ep8 ep0 in&out ep1 in ep1 out 1024 1024 ep6 1024 512 512 ep8 512 512 ep6 512 512 512 512 ep2 512 512 ep4 512 512 ep2 512 512 ep4 512 512 ep2 512 512 ep4 512 512 ep2 512 512 512 512 ep2 512 512 512 512 ep2 512 512 1024 ep2 1024 1024 ep2 1024 1024 ep2 1024 512 512 ep6 1024 1024 ep6 512 512 ep8 512 512 ep6 512 512 512 512 ep6 1024 1024 ep6 512 512 ep8 512 512 ep6 512 512 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 64 1 2 3 4 5 6 7 8 9 10 11 12 table 6. default full-sp eed alternate settings [2, 3] alternate setting 0 1 2 3 ep0 64 64 64 64 ep1out 0 64 bulk 64 int 64 int ep1in 0 64 bulk 64 int 64 int ep2 0 64 bulk out (2) 64 int out (2) 64 iso out (2) notes 2. ?0? means ?not implemented.? 3. ?2? means ?double buffered.? [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 10 of 33 default high-speed alternate settings external fifo interface architecture the nx2lp-flex slave fifo ar chitecture has eight 512-byte blocks in the endpoint ram th at directly serve as fifo memories, and are controlled by fifo control signals (such as slcs#, slrd, slwr, sloe , pktend, and flags). in operation, some of the eight ram blocks fill or empty from the sie, while the others are connected to the i/o transfer logic. the transfer logic takes two forms, the gpif for internally generated control signals, or the slave fifo interface for externally controlled transfers. master/slave control signals the nx2lp-flex endpoint fifos are implemented as eight physically distinct 256x16 ra m blocks. the 8051/sie can switch any of the ram blocks between two domains, the usb (sie) domain and the 8051-i/o unit domain. this switching is done virtually instantaneously, giving essentially zero transfer time between ?usb fifos? and ?slave fifos.? since they are physically the same memory, no bytes are actually transferred between buffers. at any given time, some ram bl ocks are filling/emptying with usb data under sie control, while other ram blocks are available to the 8051 and/or the i/o control unit. the ram blocks operate as single-por t in the usb domain, and dual-port in the 8051-i/o domain. the blocks can be configured as single, double, triple, or quad buffered as previ- ously shown. the i/o control unit implements either an internal-master (m for master) or external-maste r (s for slave) interface. in master (m) mode, the gp if internally controls fifoadr[1:0] to select a fifo. the two rdy pins can be used as flag inputs from an external fifo or other logic if desired. the gpif can be run from an internally derived clock (ifclk), at a rate that transfers data up to 96 megabytes/s (48-mhz ifclk with 16-bit interface). in slave (s) mode, the nx2lp-flex accepts an internally derived clock (ifclk, max. frequency 48 mhz) and slcs#, slrd, slwr, sloe, pktend sig nals from external logic. each endpoint can individually be selected for byte or word operation by an internal conf iguration bit, and a slave fifo output enable signal sloe enables data of the selected width. external logic must ensure that the output enable signal is inactive when writing data to a slave fifo. the slave interface must operate asynchronously, where the slrd and slwr signals act directly as strobes, rather than a clock qualifier as in a synchronous mode. the signals slrd, slwr, sloe and pktend are gated by the signal slcs#. gpif and fifo clock rates an 8051 register bit selects one of two frequencies for the internally supplied interface clock: 30 mhz and 48 mhz. a bit within the ifconfig register will invert the ifclk signal. the default nand firmware image implements a 48-mhz internally supplied interface clock. the nand boot logic uses the same configuration to implement 100-ns timing on the nand bus to support proper detection of all nand flash types. gpif the gpif is a flexible 8- or 16-bit parallel interface driven by a user-programmable finite state machine. it allows the nx2lp-flex to perform local bus mastering, and can implement a wide variety of protocols such as 8-bit nand interface, printer parallel port, and utopia. the default nand firmware and boot logic utilizes gpif functionality to interface with nand flash. the gpif on the nx2lp-flex features three programmable control outputs (ctl) and two general-purpose ready inputs (rdy). the gpif data bus width can be 8 or 16 bits. because ep4 0 64 bulk out (2) 64 bulk out (2) 64 bulk out (2) ep6 0 64 bulk in (2) 64 int in (2) 64 iso in (2) ep8 0 64 bulk in (2) 64 bulk in (2) 64 bulk in (2) table 6. default full-sp eed alternate settings [2, 3] (continued) note 4. even though these buffers are 64 bytes, they are reported as 512 for usb 2.0 compliance. the user must never transfer packets larger than 64 bytes to ep1. table 7. default high-s peed alternate settings [2, 3] alternate setting 0 1 2 3 ep0 64 64 64 64 ep1out 0 512 bulk [4] 64 int 64 int ep1in 0 512 bulk [4] 64 int 64 int ep2 0 512 bulk out (2) 512 int out (2) 512 iso out (2) ep4 0 512 bulk out (2) 512 bulk out (2) 512 bulk out (2) ep6 0 512 bulk in (2) 512 int in (2) 512 iso in (2) ep8 0 512 bulk in (2) 512 bulk in (2) 512 bulk in (2) [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 11 of 33 the default nand firmware image implements an 8-bit data bus and up to 8 chip enable pins on the gpif ports, it is recom- mended that designs based upon the default firmware image use an 8-bit data bus as well. each gpif vector defines the state of the control outputs, and determines what state a ready input (or multiple inputs) must be before proceeding. the gpif vector can be programmed to advance a fifo to the next data value, advance an address, etc. a sequence of the gpif vectors make up a single waveform that will be executed to perform the desired data move between the nx2lp-flex and the external device. three control out signals the nx2lp-flex exposes three control signals, ctl[2:0]. ctlx waveform edges can be programmed to make transi- tions as fast as once per clock (20.8 ns using a 48-mhz clock). two ready in signals the 8051 programs the gpif unit to test the rdy pins for gpif branching. the 56-pin pack age brings out two signals, rdy[1:0]. long transfer mode in gpif master mode, the 8051 appropriately sets gpif trans- action count registers (gpiftcb3, gpiftcb2, gpiftcb1, or gpiftcb0) for unattended transfers of up to 2 32 transactions. the gpif automatically throttles data flow to prevent under- or over-flow until the full number of requested transactions complete. the gpif decrements the value in these registers to represent the current status of the transaction. ecc generation [5] the nx2lp-flex can calculate eccs (error-correcting codes) on data that passes across its gpif or slave fifo interfaces. there are two ecc configurations: ? two eccs, each calculated over 256 bytes (smartmedia standard) ? one ecc calculated over 512 bytes. the two ecc configurations described below are selected by the eccm bit. the ecc can correct any one-bit error or detect any two-bit error. eccm = 0 two 3-byte eccs, each calculated over a 256-byte block of data. this configuration conforms to the smartmedia standard and is used by both the nand boot logic and default nand firmware image. when any value is written to eccreset and data is then passed across the gpif or slave fifo interface, the ecc for the first 256 bytes of data will be calculated and stored in ecc1. the ecc for the next 256 bytes of data will be stored in ecc2. after the second ecc is calculated, the values in the eccx registers will not change until eccreset is written again, even if more data is subsequently passed across the interface. eccm = 1 one 3-byte ecc calculated over a 512-byte block of data. when any value is written to eccreset and data is then passed across the gpif or slave fifo interface, the ecc for the first 512 bytes of data will be calculated and stored in ecc1; ecc2 is unused. after the ecc is calculated, the value in ecc1 will not change until eccreset is written again, even if more data is subsequently passed across the interface autopointer access nx2lp-flex provides two identical autopointers. they are similar to the internal 8051 data pointers, but with an additional feature: they can optionally increment after every memory access. also, the autopointers can point to any nx2lp-flex register or endpoint buffer space. i 2 c controller nx2lp has one i 2 c port that the 8051, once running uses to control external i 2 c devices. the i 2 c port operates in master mode only. the i 2 c post is disabled at startup and only available for use after the initial nand access. i 2 c port pins the i 2 c pins scl and sda must have external 2.2-k pull-up resistors even if no eeprom is connected to the nx2lp. i 2 c interface general-purpose access the 8051 can control peripherals connected to the i 2 c bus using the i 2 ctl and i 2 data registers. nx2lp provides i 2 c master control only and is never an i 2 c slave. note 5. to use the ecc logic, the gpif or slave fifo interface must be configured for byte-wide operation. [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 12 of 33 pin assignments figure 9 and figure 10 identify all signals for the 56-pin nx2lp-flex package. three modes of operation are available for the nx2lp-flex: port mode, gpif master mode, and slave fifo mode. these modes define the signals on the right edge of each column in figure 9 . the right-most column details the signal functionality from the default nand firmware image, which act ually utilizes gpif master mode. the signals on the left edge of the ?port? column are common to all modes of the nx2lp-flex. the 8051 selects the interface mode using the ifconfig[1:0] register bits. port mode is t he power-on default configuration. figure 10 details the pinout of the 56-pin package and lists pin names for all modes of operation. pin names with an asterisk (*) feature programmable polarity. figure 9. port and signal mapping xtalin xtalout reset# wakeup# scl sdata dplus dminus rdy0 rdy1 ctl0 ctl1 ctl2 ? pa7 ? pa6 ? pa5 ? pa4 ? pa3/wu2 ? pa2 ? pa1/int1# ? pa0/int0# ? gpio8 gpio9 ? fd[15] ? fd[14] ? fd[13] ? fd[12] ? fd[11] ? fd[10] ? fd[9] ? fd[8] ? fd[7] ? fd[6] ? fd[5] ? fd[4] ? fd[3] ? fd[2] ? fd[1] ? fd[0] slrd slwr flaga flagb flagc ? flagd/slcs#/pa7 ? pktend fifoadr1 ? fifoadr0 pa3/wu2 sloe pa1/int1# ? pa0/int0# ? gpio8 gpio9 ? fd[15] ? fd[14] ? fd[13] ? fd[12] ? fd[11] ? fd[10] ? fd[9] ? fd[8] ? fd[7] ? fd[6] ? fd[5] ? fd[4] ? fd[3] ? fd[2] ? fd[1] ? fd[0] pd7 pd6 pd5 pd4 pd3 pd2 pd1 pd0 pb7 pb6 pb5 pb4 pb3 pb2 pb1 pb0 pa7 pa6 pa5 pa4 wu2/pa3 pa2 int1#/pa1 into#/pa0 gpio8 gpio9 port gpif master slave fifo default nand ? ce7#/gpio7 ? ce6#/gpio6 ? ce5#/gpio5 ? ce4#/gpio4 ? ce3#/gpio3 ? ce2#/gpio2 ? ce1# ? ce0# ? dd7 ? dd6 ? dd5 ? dd4 ? dd3 ? dd2 ? dd1 ? dd0 r_b1# r_b2# we# re0# re1# gpio1 gpio0 wp_sw# wp_nf# led2# led1# ? ale ? cle ? gpio8 gpio9 firmware use [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 13 of 33 figure 10. cy7c68033/cy7c68034 56-pin qfn pin assignment cy7c68033/cy7c68034 56-pin qfn 28 27 26 25 24 23 22 21 20 19 18 17 16 15 43 44 45 46 47 48 49 50 51 52 53 54 55 56 1 2 3 4 5 6 7 8 9 10 11 12 13 14 42 41 40 39 38 37 36 35 34 33 32 31 30 29 reset# gnd pa7/*flagd/slcs# pa6/*pktend pa5/fifoadr1 pa4/fifoadr0 pa3/*wu2 pa2/*sloe pa1/int1# pa0/int0# vcc ctl2/*flagc ctl1/*flagb ctl0/*flaga rdy0/*slrd rdy1/*slwr avcc xtalout xtalin agnd avcc dplus dminus agnd vcc gnd gpio8 reserved# vcc *wakeup pd0/fd8 pd1/fd9 pd2/fd10 pd3/fd11 pd4/fd12 pd5/fd13 pd6/fd14 pd7/fd15 gnd gpio9 vcc gnd gnd vcc gnd pb7/fd7 pb6/fd6 pb5/fd5 pb4/fd4 pb3/fd3 pb2/fd2 pb1/fd1 pb0/fd0 vcc sdata scl [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 14 of 33 table 8. nx2lp-flex pin descriptions [6] 56 qfn pin number default pin name nand firmware usage pin type default state description 9 dminus n/a i/o/z z usb d? signal . connect to the usb d? signal. 8 dplus n/a i/o/z z usb d+ signal . connect to the usb d+ signal. 42 reset# n/a input n/a active low reset . resets the entire chip. see section ?reset and wakeup? on page 7 for more details. 5 xtalin n/a input n/a crystal input . connect this signal to a 24-mhz parallel-resonant, fundamental mode crystal and load capacitor to gnd. it is also correct to drive xtalin with an external 24-mhz square wave derived from another clock source. when driving from an external source, the driving signal should be a 3.3v square wave. 4 xtalout n/a output n/a crystal output . connect this signal to a 24-mhz parallel-resonant, fundamental mode crystal and load capacitor to gnd. if an external clock is used to drive xtalin, leave this pin open. 54 gpio9 gpio9 o/z 12 mhz gpio9 is a bidirectional io port pin. 1 rdy0 or slrd r_b1# input n/a multiplexed pin whose function is selected by ifconfig[1:0]. rdy0 is a gpif input signal. slrd is the input-only read stro be with programmable polarity (fifopinpolar[3]) for the slave fifos connected to fd[7:0] or fd[15:0]. r_b1# is a nand ready/busy input signal. 2 rdy1 or slwr r_b2# input n/a multiplexed pin whose function is selected by ifconfig[1:0]. rdy1 is a gpif input signal. slwr is the input-only write strobe with programmable polarity (fifopinpolar[2]) for the slave fifos connected to fd[7:0] or fd[15:0]. r_b2# is a nand ready/busy input signal. 29 ctl0 or flaga we# o/z h multiplexed pin whose function is selected by ifconfig[1:0]. ctl0 is a gpif control output. flaga is a programmable slave-fifo output status flag signal. defaults to programmable for the fifo sele cted by the fifoadr[1:0] pins. we# is the nand write enable output signal. 30 ctl1 or flagb re0# o/z h multiplexed pin whose functi on is selected by ifconfig[1:0]. ctl1 is a gpif control output. flagb is a programmable slave-fifo output status flag signal. defaults to full for the fifo se lected by the fi foadr[1:0] pins. re0# is a nand read enable output signal. 31 ctl2 or flagc re1# o/z h multiplexed pin whose functi on is selected by ifconfig[1:0]. ctl2 is a gpif control output. flagc is a programmable slave-fifo output status flag signal. defaults to empty for the fifo se lected by the fifo adr[1:0] pins. re1# is a nand read enable output signal. note 6. unused inputs should not be left floating. tie either high or low as appropriate. outputs should only be pulled up or down to ensure signals at power-up and i n standby. note also that no pins should be driven while the device is powered down. [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 15 of 33 13 gpio8 gpio8 i/o/z i gpio8: is a bidirectional io port pin. 14 reserved# n/a input n/a reserved . connect to ground. 15 scl n/a od z clock for the i 2 c interface. connect to vcc with a 2.2k resistor, even if no i 2 c peripheral is attached. 16 sdata n/a od z data for the i 2 c interface. connect to vcc with a 2.2k resistor, even if no i 2 c peripheral is attached. 44 wakeup unused input n/a usb wakeup . if the 8051 is in suspend, asserting this pin starts up the oscillator and interrupts the 8051 to allow it to exit the suspend mode. holding wakeup asserted in hibits the ez-usb chip from suspending. this pin has program mable polarity, controlled by wakeup[4]. port a 33 pa0 or int0# cle i/o/z i (pa0) multiplexed pin whose function is selected by portacfg[0] pa0 is a bidirectional io port pin. int0# is the active-low 8051 int0 interrupt input signal, which is either edge triggered (it0 = 1) or level triggered (it0 = 0). cle is the nand command latch enable signal. 34 pa1 or int1# ale i/o/z i (pa1) multiplexed pin whose function is selected by portacfg[1] pa1 is a bidirectional io port pin. int1# is the active-low 8051 int1 interrupt input signal, which is either edge triggered (it1 = 1) or level triggered (it1 = 0). ale is the nand address latch enable signal. 35 pa2 or sloe led1# i/o/z i (pa2) multiplexed pin whose function is selected by ifconfig[1:0]. pa2 is a bidirectional io port pin. sloe is an input-only output enabl e with programmable polarity (fifopinpolar[4]) for the slave fifos connected to fd[7:0] or fd[15:0]. led1# is the data activity indicator led sink pin. 36 pa3 or wu2 led2# i/o/z i (pa3) multiplexed pin whose function is selected by wakeup[7] and oea[3] pa3 is a bidirectional i/o port pin. wu2 is an alternate source for usb wakeup, enabled by wu2en bit (wakeup[1]) and polarity set by wu2pol (wakeup[4]). if the 8051 is in suspend and wu2en = 1, a transition on this pin starts up the oscillator and interrupts the 8051 to allow it to exit the suspend mode. asserting this pin inhibits the chip from suspending, if wu2en = 1. led2# is the chip activity indicator led sink pin. 37 pa4 or fifoadr0 wp_nf# i/o/z i (pa4) multiplexed pin whose function is selected by ifconfig[1:0]. pa4 is a bidirectional i/o port pin. fifoadr0 is an input-only address se lect for the slave fifos connected to fd[7:0] or fd[15:0]. wp_nf# is the nand write-protec t control output signal. 38 pa5 or fifoadr1 wp_sw# i/o/z i (pa5) multiplexed pin whose function is selected by ifconfig[1:0]. pa5 is a bidirectional i/o port pin. fifoadr1 is an input-only address se lect for the slave fifos connected to fd[7:0] or fd[15:0]. wp_sw# is the nand write-protect switch input signal. table 8. nx2lp-flex pin descriptions (continued) [6] 56 qfn pin number default pin name nand firmware usage pin type default state description [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 16 of 33 39 pa6 or pktend gpio0 (input) i/o/z i (pa6) multiplexed pin whose function is selected by the ifconfig[1:0] bits. pa6 is a bidirectional i/o port pin. pktend is an input used to commit the fifo packet data to the endpoint and whose polarity is programmable via fifopin- polar[5]. gpio1 is a general purpose i/o signal. 40 pa7 or flagd or slcs# gpio1 (input) i/o/z i (pa7) multiplexed pin whose function is selected by the ifconfig[1:0] and portacfg[7] bits. pa7 is a bidirectional i/o port pin. flagd is a programmable slave-fifo output status flag signal. slcs# gates all other slave fifo enable/strobes gpio0 is a general purpose i/o signal. port b 18 pb0 or fd[0] dd0 i/o/z i (pb0) multiplexed pin whose function is selected by ifconfig[1:0]. pb0 is a bidirectional i/o port pin. fd[0] is the bidirectional fifo/gpif data bus. dd0 is a bidirectional nand data bus signal. 19 pb1 or fd[1] dd1 i/o/z i (pb1) multiplexed pin whose function is selected by ifconfig[1:0]. pb1 is a bidirectional i/o port pin. fd[1] is the bidirectional fifo/gpif data bus. dd1 is a bidirectional nand data bus signal. 20 pb2 or fd[2] dd2 i/o/z i (pb2) multiplexed pin whose function is selected by ifconfig[1:0]. pb2 is a bidirectional i/o port pin. fd[2] is the bidirectional fifo/gpif data bus. dd2 is a bidirectional nand data bus signal. 21 pb3 or fd[3] dd3 i/o/z i (pb3) multiplexed pin whose function is selected by ifconfig[1:0]. pb3 is a bidirectional i/o port pin. fd[3] is the bidirectional fifo/gpif data bus. dd3 is a bidirectional nand data bus signal. 22 pb4 or fd[4] dd4 i/o/z i (pb4) multiplexed pin whose function is selected by ifconfig[1:0]. pb4 is a bidirectional i/o port pin. fd[4] is the bidirectional fifo/gpif data bus. dd4 is a bidirectional nand data bus signal. 23 pb5 or fd[5] dd5 i/o/z i (pb5) multiplexed pin whose function is selected by ifconfig[1:0]. pb5 is a bidirectional i/o port pin. fd[5] is the bidirectional fifo/gpif data bus. dd5 is a bidirectional nand data bus signal. 24 pb6 or fd[6] dd6 i/o/z i (pb6) multiplexed pin whose function is selected by ifconfig[1:0]. pb6 is a bidirectional i/o port pin. fd[6] is the bidirectional fifo/gpif data bus. dd6 is a bidirectional nand data bus signal. 25 pb7 or fd[7] dd7 i/o/z i (pb7) multiplexed pin whose function is selected by ifconfig[1:0]. pb7 is a bidirectional i/o port pin. fd[7] is the bidirectional fifo/gpif data bus. dd7 is a bidirectional nand data bus signal. port d 45 pd0 or fd[8] ce0# i/o/z i (pd0) multiplexed pin whose function is selected by the ifconfig[1:0] and epxfifocfg.0 (wordwide) bits. fd[8] is the bidirectional fifo/gpif data bus. ce0# is a nand chip enable output signal. table 8. nx2lp-flex pin descriptions (continued) [6] 56 qfn pin number default pin name nand firmware usage pin type default state description [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 17 of 33 46 pd1 or fd[9] ce1# i/o/z i (pd1) multiplexed pin whose function is selected by the ifconfig[1:0] and epxfifocfg.0 (wordwide) bits. fd[9] is the bidirectional fifo/gpif data bus. ce1# is a nand chip enable output signal. 47 pd2 or fd[10] ce2# or gpio2 i/o/z i (pd2) multiplexed pin whose function is selected by the ifconfig[1:0] and epxfifocfg.0 (wordwide) bits. fd[10] is the bidirectional fifo/gpif data bus. ce2# is a nand chip enable output signal. gpio2 is a general purpose i/o signal. 48 pd3 or fd[11] ce3# or gpio3 i/o/z i (pd3) multiplexed pin whose function is selected by the ifconfig[1:0] and epxfifocfg.0 (wordwide) bits. fd[11] is the bidirectional fifo/gpif data bus. ce3# is a nand chip enable output signal. gpio3 is a general purpose i/o signal. 49 pd4 or fd[12] ce4# or gpio4 i/o/z i (pd4) multiplexed pin whose function is selected by the ifconfig[1:0] and epxfifocfg.0 (wordwide) bits. fd[12] is the bidirectional fifo/gpif data bus. ce4# is a nand chip enable output signal. gpio4 is a general purpose i/o signal. 50 pd5 or fd[13] ce5# or gpio5 i/o/z i (pd5) multiplexed pin whose function is selected by the ifconfig[1:0] and epxfifocfg.0 (wordwide) bits. fd[13] is the bidirectional fifo/gpif data bus. ce5# is a nand chip enable output signal. gpio5 is a general purpose i/o signal. 51 pd6 or fd[14] ce6# or gpio6 i/o/z i (pd6) multiplexed pin whose function is selected by the ifconfig[1:0] and epxfifocfg.0 (wordwide) bits. fd[14] is the bidirectional fifo/gpif data bus. ce6# is a nand chip enable output signal. gpio6 is a general purpose i/o signal. 52 pd7 or fd[15] ce7# or gpio7 i/o/z i (pd7) multiplexed pin whose function is selected by the ifconfig[1:0] and epxfifocfg.0 (wordwide) bits. fd[15] is the bidirectional fifo/gpif data bus. ce7# is a nand chip enable output signal. gpio7 is a general purpose i/o signal. power and ground 3 7 avcc n/a power n/a analog v cc . connect this pin to 3.3v power source. this signal provides power to the analog section of the chip. 6 10 agnd n/a ground n/a analog ground . connect to ground with as short a path as possible. 11 17 27 32 43 55 vcc n/a power n/a v cc . connect to 3.3v power source. 12 26 28 41 53 56 gnd n/a ground n/a ground . table 8. nx2lp-flex pin descriptions (continued) [6] 56 qfn pin number default pin name nand firmware usage pin type default state description [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 18 of 33 register summary nx2lp-flex register bit definitions are described in the ez-usb trm in greater detail. some registers that are listed here and in the trm do not apply to the nx2lp-flex. they are kept here for consistency reasons only. registers that do not apply to the nx2lp-flex should be left at their default power-up values. table 9. nx2lp-flex register summary hex size name description b7 b6 b5 b4 b3 b2 b1 b0 default access gpif waveform memories e400 128 wavedata gpif waveform descriptor 0, 1, 2, 3 data d7 d6 d5 d4 d3 d2 d1 d0 xxxxxxxx rw e480 128 reserved general configuration e50d gpcr2 general purpose configu- ration register 2 reserved reserved reserved full_spee d_only reserved reserved reserved reserved 00000000 r e600 1 cpucs cpu control & status 0 0 portcstb clkspd1 clkspd0 clkinv clkoe 8051res 00000010 rrbbbbbr e601 1 ifconfig interface configuration (ports, gpif, slave fifos) 1 3048mhz 0 ifclkpol async gstate ifcfg1 ifcfg0 10000000 rw e602 1 pinflagsab [7] slave fifo flaga and flagb pin configuration flagb3 flagb2 flagb1 flagb0 flaga3 flaga2 flaga1 flaga0 00000000 rw e603 1 pinflagscd [7] slave fifo flagc and flagd pin configuration flagd3 flagd2 flagd1 flagd0 flagc3 flagc2 flagc1 flagc0 00000000 rw e604 1 fiforeset [7] restore fifos to default state nakall 0 0 0 ep3 ep2 ep1 ep0 xxxxxxxx w e605 1 breakpt breakpoint control 0 0 0 0 break bppulse bpen 0 00000000 rrrrbbbr e606 1 bpaddrh breakpoint address h a15 a14 a13 a12 a11 a10 a9 a8 xxxxxxxx rw e607 1 bpaddrl breakpoint address l a7 a6 a5 a4 a3 a2 a1 a0 xxxxxxxx rw e608 1 uart230 230 kbaud internally generated ref. clock 0 0 0 0 0 0 230uart1 230uart0 00000000 rrrrrrbb e609 1 fifopinpolar [7] slave fifo interface pins polarity 0 0 pktend sloe slrd slwr ef ff 00000000 rrbbbbbb e60a 1 revid chip revision rv7 rv6 rv5 rv4 rv3 rv2 rv1 rv0 reva 00000001 r e60b 1 revctl [7] chip revision control 0 0 0 0 0 0 dyn_out enh_pkt 00000000 rrrrrrbb udma e60c 1 gpifholdamount mstb hold time (for udma) 0 0 0 0 0 0 holdtime1 holdtime0 00000000 rrrrrrbb 3 reserved endpoint configuration e610 1 ep1outcfg endpoint 1-out configuration valid 0 type1 type0 0 0 0 0 10100000 brbbrrrr e611 1 ep1incfg endpoint 1-in configuration valid 0 type1 type0 0 0 0 0 10100000 brbbrrrr e612 1 ep2cfg endpoint 2 configuration valid dir type1 type0 size 0 buf1 buf0 10100010 bbbbbrbb e613 1 ep4cfg endpoint 4 configuration valid dir type1 type0 0 0 0 0 10100000 bbbbrrrr e614 1 ep6cfg endpoint 6 configuration valid dir type1 type0 size 0 buf1 buf0 11100010 bbbbbrbb e615 1 ep8cfg endpoint 8 configuration valid dir type1 type0 0 0 0 0 11100000 bbbbrrrr 2 reserved e618 1 ep2fifocfg [7] endpoint 2/slave fifo configuration 0 infm1 oep1 autoout autoin zerolenin 0 wordwide 00000101 rbbbbbrb e619 1 ep4fifocfg [7] endpoint 4/slave fifo configuration 0 infm1 oep1 autoout autoin zerolenin 0 wordwide 00000101 rbbbbbrb e61a 1 ep6fifocfg [7] endpoint 6/slave fifo configuration 0 infm1 oep1 autoout autoin zerolenin 0 wordwide 00000101 rbbbbbrb e61b 1 ep8fifocfg [7] endpoint 8/slave fifo configuration 0 infm1 oep1 autoout autoin zerolenin 0 wordwide 00000101 rbbbbbrb e61c 4 reserved e620 1 ep2autoinlenh [7 endpoint 2 autoin packet length h 0 0 0 0 0 pl10 pl9 pl8 00000010 rrrrrbbb e621 1 ep2autoinlenl [7] endpoint 2 autoin packet length l pl7 pl6 pl5 pl4 pl3 pl2 pl1 pl0 00000000 rw e622 1 ep4autoinlenh [7] endpoint 4 autoin packet length h 0 0 0 0 0 0 pl9 pl8 00000010 rrrrrrbb e623 1 ep4autoinlenl [7] endpoint 4 autoin packet length l pl7 pl6 pl5 pl4 pl3 pl2 pl1 pl0 00000000 rw e624 1 ep6autoinlenh [7] endpoint 6 autoin packet length h 0 0 0 0 0 pl10 pl9 pl8 00000010 rrrrrbbb e625 1 ep6autoinlenl [7] endpoint 6 autoin packet length l pl7 pl6 pl5 pl4 pl3 pl2 pl1 pl0 00000000 rw e626 1 ep8autoinlenh [7] endpoint 8 autoin packet length h 0 0 0 0 0 0 pl9 pl8 00000010 rrrrrrbb e627 1 ep8autoinlenl [7] endpoint 8 autoin packet length l pl7 pl6 pl5 pl4 pl3 pl2 pl1 pl0 00000000 rw e628 1 ecccfg ecc configuration 0 0 0 0 0 0 0 eccm 00000000 rrrrrrrb note 7. read and writes to these registers may require synchronization delay, see the technical reference manual for ?synchronization delay.? [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 19 of 33 e629 1 eccreset ecc reset x x x x x x x x 00000000 w e62a 1 ecc1b0 ecc1 byte 0 address line15 line14 line13 line12 line11 line10 line9 line8 00000000 r e62b 1 ecc1b1 ecc1 byte 1 address line7 line6 line5 line4 line3 line2 line1 line0 00000000 r e62c 1 ecc1b2 ecc1 byte 2 address col5 col4 col3 col2 col1 col0 line17 line16 00000000 r e62d 1 ecc2b0 ecc2 byte 0 address line15 line14 line13 line12 line11 line10 line9 line8 00000000 r e62e 1 ecc2b1 ecc2 byte 1 address line7 line6 line5 line4 line3 line2 line1 line0 00000000 r e62f 1 ecc2b2 ecc2 byte 2 address col5 col4 col3 col2 col1 col0 0 0 00000000 r e630 h.s. 1 ep2fifopfh [7] endpoint 2/slave fifo programmable flag h decis pktstat in:pkts[2] out:pfc12 in:pkts[1] out:pfc11 in:pkts[0] out:pfc10 0 pfc9 pfc8 10001000 bbbbbrbb e630 f. s . 1 ep2fifopfh [7] endpoint 2/slave fifo programmable flag h decis pktstat out:pfc12 out:pfc11 out:pfc10 0 pfc9 in:pkts[2] out:pfc8 10001000 bbbbbrbb e631 h.s. 1 ep2fifopfl [7] endpoint 2/slave fifo programmable flag l pfc7 pfc6 pfc5 pfc4 pfc3 pfc2 pfc1 pfc0 00000000 rw e631 f. s 1 ep2fifopfl [7] endpoint 2/slave fifo programmable flag l in:pkts[1] out:pfc7 in:pkts[0] out:pfc6 pfc5 pfc4 pfc3 pfc2 pfc1 pfc0 00000000 rw e632 h.s. 1 ep4fifopfh [7] endpoint 4/slave fifo programmable flag h decis pktstat 0 in: pkts[1] out:pfc10 in: pkts[0] out:pfc9 0 0 pfc8 10001000 bbrbbrrb e632 f. s 1 ep4fifopfh [7] endpoint 4/slave fifo programmable flag h decis pktstat 0 out:pfc10 out:pfc9 0 0 pfc8 10001000 bbrbbrrb e633 h.s. 1 ep4fifopfl [7] endpoint 4/slave fifo programmable flag l pfc7 pfc6 pfc5 pfc4 pfc3 pfc2 pfc1 pfc0 00000000 rw e633 f. s 1 ep4fifopfl [7] endpoint 4/slave fifo programmable flag l in: pkts[1] out:pfc7 in: pkts[0] out:pfc6 pfc5 pfc4 pfc3 pfc2 pfc1 pfc0 00000000 rw e634 h.s. 1 ep6fifopfh [7] endpoint 6/slave fifo programmable flag h decis pktstat in:pkts[2] out:pfc12 in:pkts[1] out:pfc11 in:pkts[0] out:pfc10 0 pfc9 pfc8 00001000 bbbbbrbb e634 f. s 1 ep6fifopfh [7] endpoint 6/slave fifo programmable flag h decis pktstat out:pfc12 out:pfc11 out:pfc10 0 pfc9 in:pkts[2] out:pfc8 00001000 bbbbbrbb e635 h.s. 1 ep6fifopfl [7] endpoint 6/slave fifo programmable flag l pfc7 pfc6 pfc5 pfc4 pfc3 pfc2 pfc1 pfc0 00000000 rw e635 f. s 1 ep6fifopfl [7] endpoint 6/slave fifo programmable flag l in:pkts[1] out:pfc7 in:pkts[0] out:pfc6 pfc5 pfc4 pfc3 pfc2 pfc1 pfc0 00000000 rw e636 h.s. 1 ep8fifopfh [7] endpoint 8/slave fifo programmable flag h decis pktstat 0 in: pkts[1] out:pfc10 in: pkts[0] out:pfc9 0 0 pfc8 00001000 bbrbbrrb e636 f. s 1 ep8fifopfh [7] endpoint 8/slave fifo programmable flag h decis pktstat 0 out:pfc10 out:pfc9 0 0 pfc8 00001000 bbrbbrrb e637 h.s. 1 ep8fifopfl [7] endpoint 8/slave fifo programmable flag l pfc7 pfc6 pfc5 pfc4 pfc3 pfc2 pfc1 pfc0 00000000 rw e637 f. s 1 ep8fifopfl [7] endpoint 8/slave fifo programmable flag l in: pkts[1] out:pfc7 in: pkts[0] out:pfc6 pfc5 pfc4 pfc3 pfc2 pfc1 pfc0 00000000 rw 8 reserved e640 1 ep2isoinpkts ep2 (if iso) in packets per frame (1-3) aadj 0 0 0 0 0 inppf1 inppf0 00000001 brrrrrbb e641 1 ep4isoinpkts ep4 (if iso) in packets per frame (1-3) aadj 0 0 0 0 0 inppf1 inppf0 00000001 brrrrrrr e642 1 ep6isoinpkts ep6 (if iso) in packets per frame (1-3) aadj 0 0 0 0 0 inppf1 inppf0 00000001 brrrrrbb e643 1 ep8isoinpkts ep8 (if iso) in packets per frame (1-3) aadj 0 0 0 0 0 inppf1 inppf0 00000001 brrrrrrr e644 4 reserved e648 1 inpktend [7] force in packet end skip 0 0 0 ep3 ep2 ep1 ep0 xxxxxxxx w e649 7 outpktend [7] force out packet end skip 0 0 0 ep3 ep2 ep1 ep0 xxxxxxxx w interrupts e650 1 ep2fifoie [7] endpoint 2 slave fifo flag interrupt enable 0 0 0 0 edgepf pf ef ff 00000000 rw e651 1 ep2fifoirq [7,8] endpoint 2 slave fifo flag interrupt request 0 0 0 0 0 pf ef ff 00000000 rrrrrbbb e652 1 ep4fifoie [7] endpoint 4 slave fifo flag interrupt enable 0 0 0 0 edgepf pf ef ff 00000000 rw e653 1 ep4fifoirq [7,8] endpoint 4 slave fifo flag interrupt request 0 0 0 0 0 pf ef ff 00000000 rrrrrbbb e654 1 ep6fifoie [7] endpoint 6 slave fifo flag interrupt enable 0 0 0 0 edgepf pf ef ff 00000000 rw e655 1 ep6fifoirq [7,8] endpoint 6 slave fifo flag interrupt request 0 0 0 0 0 pf ef ff 00000000 rrrrrbbb e656 1 ep8fifoie [7] endpoint 8 slave fifo flag interrupt enable 0 0 0 0 edgepf pf ef ff 00000000 rw e657 1 ep8fifoirq [7,8] endpoint 8 slave fifo flag interrupt request 0 0 0 0 0 pf ef ff 00000000 rrrrrbbb e658 1 ibnie in-bulk-nak interrupt enable 0 0 ep8 ep6 ep4 ep2 ep1 ep0 00000000 rw e659 1 ibnirq [8] in-bulk-nak interrupt request 0 0 ep8 ep6 ep4 ep2 ep1 ep0 00xxxxxx rrbbbbbb e65a 1 nakie endpoint ping-nak/ibn interrupt enable ep8 ep6 ep4 ep2 ep1 ep0 0 ibn 00000000 rw table 9. nx2lp-flex register summary (continued) hex size name description b7 b6 b5 b4 b3 b2 b1 b0 default access note 8. the register can only be reset, it cannot be set. [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 20 of 33 e65b 1 nakirq [8] endpoint ping-nak/ibn interrupt request ep8 ep6 ep4 ep2 ep1 ep0 0 ibn xxxxxx0x bbbbbbrb e65c 1 usbie usb int enables 0 ep0ack hsgrant ures susp sutok sof sudav 00000000 rw e65d 1 usbirq [8] usb interrupt requests 0 ep0ack hsgrant ures susp sutok sof sudav 0xxxxxxx rbbbbbbb e65e 1 epie endpoint interrupt enables ep8 ep6 ep4 ep2 ep1out ep1in ep0out ep0in 00000000 rw e65f 1 epirq [8] endpoint interrupt requests ep8 ep6 ep4 ep2 ep1out ep1in ep0out ep0in 0 rw e660 1 gpifie [7] gpif interrupt enable 0 0 0 0 0 0 gpifwf gpifdone 00000000 rw e661 1 gpifirq [7] gpif interrupt request 0 0 0 0 0 0 gpifwf gpifdone 000000xx rw e662 1 usberrie usb error interrupt enables isoep8 isoep6 isoep4 isoep2 0 0 0 errlimit 00000000 rw e663 1 usberrirq [8] usb error interrupt requests isoep8 isoep6 isoep4 isoep2 0 0 0 errlimit 0000000x bbbbrrrb e664 1 errcntlim usb error counter and limit ec3 ec2 ec1 ec0 limit3 limit2 limit1 limit0 xxxx0100 rrrrbbbb e665 1 clrerrcnt clear error counter ec3:0 x x x x x x x x xxxxxxxx w e666 1 int2ivec interrupt 2 (usb) autovector 0 i2v4 i2v3 i2v2 i2v1 i2v0 0 0 00000000 r e667 1 int4ivec interrupt 4 (slave fifo & gpif) autovector 1 0 i4v3 i4v2 i4v1 i4v0 0 0 10000000 r e668 1 intset-up interrupt 2&4 setup 0 0 0 0 av2en 0 int4src av4en 00000000 rw e669 7 reserved input/output e670 1 portacfg i/o porta alternate configuration flagd slcs 0 0 0 0 int1 int0 00000000 rw e671 1 portccfg i/o portc alternate configuration gpifa7 gpifa6 gpifa5 gpifa4 gpifa3 gpifa2 gpifa1 gpifa0 00000000 rw e672 1 portecfg i/o porte alternate configuration gpifa8 t2ex int6 rxd1out rxd0out t2out t1out t0out 00000000 rw e673 4 xtalinsrc xtalin clock source 0 0 0 0 0 0 0 extclk 00000000 rrrrrrrb e677 1 reserved e678 1 i2cs i 2 c bus control & status start stop lastrd id1 id0 berr ack done 000xx000 bbbrrrrr e679 1 i2dat i 2 c bus data d7 d6 d5 d4 d3 d2 d1 d0 xxxxxxxx rw e67a 1 i2ctl i 2 c bus control 0 0 0 0 0 0 stopie 400khz 00000000 rw e67b 1 xautodat1 autoptr1 movx access, when aptren=1 d7 d6 d5 d4 d3 d2 d1 d0 xxxxxxxx rw e67c 1 xautodat2 autoptr2 movx access, when aptren=1 d7 d6 d5 d4 d3 d2 d1 d0 xxxxxxxx rw udma crc e67d 1 udmacrch [7] udma crc msb crc15 crc14 crc13 crc12 crc11 crc10 crc9 crc8 01001010 rw e67e 1 udmacrcl [7] udma crc lsb crc7 crc6 crc5 crc4 crc3 crc2 crc1 crc0 10111010 rw e67f 1 udmacrc- qualifier udma crc qualifier qenable 0 0 0 qstate qsignal2 qsignal1 qsignal0 00000000 brrrbbbb usb control e680 1 usbcs usb control & status hsm 0 0 0 discon nosynsof renum sigrsume x0000000 rrrrbbbb e681 1 suspend put chip into suspend x x x x x x x x xxxxxxxx w e682 1 wakeupcs wakeup control & status wu2 wu wu2pol wupol 0 dpen wu2en wuen xx000101 bbbbrbbb e683 1 togctl toggle control q s r io ep3 ep2 ep1 ep0 x0000000 rrrbbbbb e684 1 usbframeh usb frame count h 0 0 0 0 0 fc10 fc9 fc8 00000xxx r e685 1 usbframel usb frame count l fc7 fc6 fc5 fc4 fc3 fc2 fc1 fc0 xxxxxxxx r e686 1 microframe microframe count, 0-7 0 0 0 0 0 mf2 mf1 mf0 00000xxx r e687 1 fnaddr usb function address 0 fa6 fa5 fa4 fa3 fa2 fa1 fa0 0xxxxxxx r e688 2 reserved endpoints e68a 1 ep0bch [7] endpoint 0 byte count h (bc15) (bc14) (bc13) (bc12) (bc11) (bc10) (bc9) (bc8) xxxxxxxx rw e68b 1 ep0bcl [7] endpoint 0 byte count l (bc7) bc6 bc5 bc4 bc3 bc2 bc1 bc0 xxxxxxxx rw e68c 1 reserved e68d 1 ep1outbc endpoint 1 out byte count 0 bc6 bc5 bc4 bc3 bc2 bc1 bc0 0xxxxxxx rw e68e 1 reserved e68f 1 ep1inbc endpoint 1 in byte count 0 bc6 bc5 bc4 bc3 bc2 bc1 bc0 0xxxxxxx rw e690 1 ep2bch [7] endpoint 2 byte count h 0 0 0 0 0 bc10 bc9 bc8 00000xxx rw e691 1 ep2bcl [7] endpoint 2 byte count l bc7/skip bc6 bc5 bc4 bc3 bc2 bc1 bc0 xxxxxxxx rw e692 2 reserved e694 1 ep4bch [7] endpoint 4 byte count h 0 0 0 0 0 0 bc9 bc8 000000xx rw e695 1 ep4bcl [7] endpoint 4 byte count l bc7/skip bc6 bc5 bc4 bc3 bc2 bc1 bc0 xxxxxxxx rw e696 2 reserved e698 1 ep6bch [7] endpoint 6 byte count h 0 0 0 0 0 bc10 bc9 bc8 00000xxx rw e699 1 ep6bcl [7] endpoint 6 byte count l bc7/skip bc6 bc5 bc4 bc3 bc2 bc1 bc0 xxxxxxxx rw e69a 2 reserved e69c 1 ep8bch [7] endpoint 8 byte count h 0 0 0 0 0 0 bc9 bc8 000000xx rw e69d 1 ep8bcl [7] endpoint 8 byte count l bc7/skip bc6 bc5 bc4 bc3 bc2 bc1 bc0 xxxxxxxx rw table 9. nx2lp-flex register summary (continued) hex size name description b7 b6 b5 b4 b3 b2 b1 b0 default access [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 21 of 33 e69e 2 reserved e6a0 1 ep0cs endpoint 0 control and status hsnak 0 0 0 0 0 busy stall 10000000 bbbbbbrb e6a1 1 ep1outcs endpoint 1 out control and status 0 0 0 0 0 0 busy stall 00000000 bbbbbbrb e6a2 1 ep1incs endpoint 1 in control and status 0 0 0 0 0 0 busy stall 00000000 bbbbbbrb e6a3 1 ep2cs endpoint 2 control and status 0 npak2 npak1 npak0 full empty 0 stall 00101000 rrrrrrrb e6a4 1 ep4cs endpoint 4 control and status 0 0 npak1 npak0 full empty 0 stall 00101000 rrrrrrrb e6a5 1 ep6cs endpoint 6 control and status 0 npak2 npak1 npak0 full empty 0 stall 00000100 rrrrrrrb e6a6 1 ep8cs endpoint 8 control and status 0 0 npak1 npak0 full empty 0 stall 00000100 rrrrrrrb e6a7 1 ep2fifoflgs endpoint 2 slave fifo flags 0 0 0 0 0 pf ef ff 00000010 r e6a8 1 ep4fifoflgs endpoint 4 slave fifo flags 0 0 0 0 0 pf ef ff 00000010 r e6a9 1 ep6fifoflgs endpoint 6 slave fifo flags 0 0 0 0 0 pf ef ff 00000110 r e6aa 1 ep8fifoflgs endpoint 8 slave fifo flags 0 0 0 0 0 pf ef ff 00000110 r e6ab 1 ep2fifobch endpoint 2 slave fifo total byte count h 0 0 0 bc12 bc11 bc10 bc9 bc8 00000000 r e6ac 1 ep2fifobcl endpoint 2 slave fifo total byte count l bc7 bc6 bc5 bc4 bc3 bc2 bc1 bc0 00000000 r e6ad 1 ep4fifobch endpoint 4 slave fifo total byte count h 0 0 0 0 0 bc10 bc9 bc8 00000000 r e6ae 1 ep4fifobcl endpoint 4 slave fifo total byte count l bc7 bc6 bc5 bc4 bc3 bc2 bc1 bc0 00000000 r e6af 1 ep6fifobch endpoint 6 slave fifo total byte count h 0 0 0 0 bc11 bc10 bc9 bc8 00000000 r e6b0 1 ep6fifobcl endpoint 6 slave fifo total byte count l bc7 bc6 bc5 bc4 bc3 bc2 bc1 bc0 00000000 r e6b1 1 ep8fifobch endpoint 8 slave fifo total byte count h 0 0 0 0 0 bc10 bc9 bc8 00000000 r e6b2 1 ep8fifobcl endpoint 8 slave fifo total byte count l bc7 bc6 bc5 bc4 bc3 bc2 bc1 bc0 00000000 r e6b3 1 sudptrh setup data pointer high address byte a15 a14 a13 a12 a11 a10 a9 a8 xxxxxxxx rw e6b4 1 sudptrl setup data pointer low ad- dress byte a7 a6 a5 a4 a3 a2 a1 0 xxxxxxx0 bbbbbbbr e6b5 1 sudptrctl setup data pointer auto mode 0 0 0 0 0 0 0 sdpauto 00000001 rw 2 reserved e6b8 8 set-updat 8 bytes of setup data d7 d6 d5 d4 d3 d2 d1 d0 xxxxxxxx r set-updat[0] = bmrequesttype set-updat[1] = bmrequest set-updat[2:3] = wval- ue set-updat[4:5] = wind- ex set-updat[6:7] = wlength gpif e6c0 1 gpifwfselect waveform selector singlewr1 singlewr0 singlerd1 singlerd0 fifowr1 fifowr0 fiford1 fiford0 11100100 rw e6c1 1 gpifidlecs gpif done, gpif idle drive mode done 0 0 0 0 0 0 idledrv 10000000 rw e6c2 1 gpifidlectl inactive bus, ctl states 0 0 ctl5 ctl4 ctl3 ctl2 ctl1 ctl0 11111111 rw e6c3 1 gpifctlcfg ctl drive type trictl 0 ctl5 ctl4 ctl3 ctl2 ctl1 ctl0 00000000 rw e6c4 1 gpifadrh [7] gpif address h 0 0 0 0 0 0 0 gpifa8 00000000 rw e6c5 1 gpifadrl [7] gpif address l gpifa7 gpifa6 gpifa5 gpifa4 gpifa3 gpifa2 gpifa1 gpifa0 00000000 rw flowstate e6c6 1 flowstate flowstate enable and selector fse 0 0 0 0 fs2 fs1 fs0 00000000 brrrrbbb e6c7 1 flowlogic flowstate logic lfunc1 lfunc0 terma2 terma1 terma0 termb2 termb1 termb0 00000000 rw e6c8 1 floweq0ctl ctl-pin states in flowstate (when logic = 0) ctl0e3 ctl0e2 ctl0e1/ ctl5 ctl0e0/ ctl4 ctl3 ctl2 ctl1 ctl0 00000000 rw e6c9 1 floweq1ctl ctl-pin states in flow- state (when logic = 1) ctl0e3 ctl0e2 ctl0e1/ ctl5 ctl0e0/ ctl4 ctl3 ctl2 ctl1 ctl0 00000000 rw e6ca 1 flowholdoff holdoff configuration hoperiod3 hoperiod2 hoperiod1 hoperiod 0 hostate hoctl2 hoctl1 hoctl0 00010010 rw e6cb 1 flowstb flowstate strobe configuration slave rdyasync ctltogl sustain 0 mstb2 mstb1 mstb0 00100000 rw e6cc 1 flowstbedge flowstate rising/falling edge configuration 0 0 0 0 0 0 falling rising 00000001 rrrrrrbb table 9. nx2lp-flex register summary (continued) hex size name description b7 b6 b5 b4 b3 b2 b1 b0 default access [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 22 of 33 e6cd 1 flowstbperiod master-strobe half-period d7 d6 d5 d4 d3 d2 d1 d0 00000010 rw e6ce 1 gpiftcb3 [7] gpif transaction count byte 3 tc31 tc30 tc29 tc28 tc27 tc26 tc25 tc24 00000000 rw e6cf 1 gpiftcb2 [7] gpif transaction count byte 2 tc23 tc22 tc21 tc20 tc19 tc18 tc17 tc16 00000000 rw e6d0 1 gpiftcb1 [7] gpif transaction count byte 1 tc15 tc14 tc13 tc12 tc11 tc10 tc9 tc8 00000000 rw e6d1 1 gpiftcb0 [7] gpif transaction count byte 0 tc7 tc6 tc5 tc4 tc3 tc2 tc1 tc0 00000001 rw 2 reserved 00000000 rw reserved reserved 1 e6d2 1 ep2gpifflgsel [7] endpoint 2 gpif flag select 0 0 0 0 0 0 fs1 fs0 00000000 rw e6d3 1 ep2gpifpfstop endpoint 2 gpif stop transaction on prog. flag 0 0 0 0 0 0 0 fifo2flag 00000000 rw e6d4 1 ep2gpiftrig [7] endpoint 2 gpif trigger x x x x x x x x xxxxxxxx w 3 reserved reserved reserved e6da 1 ep4gpifflgsel [7] endpoint 4 gpif flag select 0 0 0 0 0 0 fs1 fs0 00000000 rw e6db 1 ep4gpifpfstop endpoint 4 gpif stop transaction on gpif flag 0 0 0 0 0 0 0 fifo4flag 00000000 rw e6dc 1 ep4gpiftrig [7] endpoint 4 gpif trigger x x x x x x x x xxxxxxxx w 3 reserved reserved reserved e6e2 1 ep6gpifflgsel [7] endpoint 6 gpif flag select 0 0 0 0 0 0 fs1 fs0 00000000 rw e6e3 1 ep6gpifpfstop endpoint 6 gpif stop transaction on prog. flag 0 0 0 0 0 0 0 fifo6flag 00000000 rw e6e4 1 ep6gpiftrig [7] endpoint 6 gpif trigger x x x x x x x x xxxxxxxx w 3 reserved reserved reserved e6ea 1 ep8gpifflgsel [7] endpoint 8 gpif flag select 0 0 0 0 0 0 fs1 fs0 00000000 rw e6eb 1 ep8gpifpfstop endpoint 8 gpif stop transaction on prog. flag 0 0 0 0 0 0 0 fifo8flag 00000000 rw e6ec 1 ep8gpiftrig [7] endpoint 8 gpif trigger x x x x x x x x xxxxxxxx w 3 reserved e6f0 1 xgpifsgldath gpif data h (16-bit mode only) d15 d14 d13 d12 d11 d10 d9 d8 xxxxxxxx rw e6f1 1 xgpifsgldatlx read/write gpif data l & trigger transaction d7 d6 d5 d4 d3 d2 d1 d0 xxxxxxxx rw e6f2 1 xgpifsgldatl- nox read gpif data l, no transaction trigger d7 d6 d5 d4 d3 d2 d1 d0 xxxxxxxx r e6f3 1 gpifreadycfg internal rdy, sync/async, rdy pin states intrdy sas tcxrdy5 0 0 0 0 0 00000000 bbbrrrrr e6f4 1 gpifreadystat gpif ready status 0 0 rdy5 rdy4 rdy3 rdy2 rdy1 rdy0 00xxxxxx r e6f5 1 gpifabort abort gpif waveforms x x x x x x x x xxxxxxxx w e6f6 2 reserved endpoint buffers e740 64 ep0buf ep0-in/-out buffer d7 d6 d5 d4 d3 d2 d1 d0 xxxxxxxx rw e780 64 ep10utbuf ep1-out buffer d7 d6 d5 d4 d3 d2 d1 d0 xxxxxxxx rw e7c0 64 ep1inbuf ep1-in buffer d7 d6 d5 d4 d3 d2 d1 d0 xxxxxxxx rw 2048 reserved rw f000 1024 ep2fifobuf 512/1024-byte ep 2/slave fifo buffer (in or out) d7 d6 d5 d4 d3 d2 d1 d0 xxxxxxxx rw f400 512 ep4fifobuf 512 byte ep 4/slave fifo buffer (in or out) d7 d6 d5 d4 d3 d2 d1 d0 xxxxxxxx rw f600 512 reserved f800 1024 ep6fifobuf 512/1024-byte ep 6/slave fifo buffer (in or out) d7 d6 d5 d4 d3 d2 d1 d0 xxxxxxxx rw fc00 512 ep8fifobuf 512 byte ep 8/slave fifo buffer (in or out) d7 d6 d5 d4 d3 d2 d1 d0 xxxxxxxx rw fe00 512 reserved xxxx i2c configuration byte 0 discon 0 0 0 0 0 400khz xxxxxxxx [10] n/a special function registers (sfrs) 80 1 ioa [9] port a (bit addressable) d7 d6 d5 d4 d3 d2 d1 d0 xxxxxxxx rw 81 1 sp stack pointer d7 d6 d5 d4 d3 d2 d1 d0 00000111 rw 82 1 dpl0 data pointer 0 l a7 a6 a5 a4 a3 a2 a1 a0 00000000 rw table 9. nx2lp-flex register summary (continued) hex size name description b7 b6 b5 b4 b3 b2 b1 b0 default access [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 23 of 33 83 1 dph0 data pointer 0 h a15 a14 a13 a12 a11 a10 a9 a8 00000000 rw 84 1 dpl1 [9] data pointer 1 l a7 a6 a5 a4 a3 a2 a1 a0 00000000 rw 85 1 dph1 [9] data pointer 1 h a15 a14 a13 a12 a11 a10 a9 a8 00000000 rw 86 1 dps [9] data pointer 0/1 select 0 0 0 0 0 0 0 sel 00000000 rw 87 1 pcon power control smod0 x 1 1 x x x idle 00110000 rw 88 1 tcon timer/counter control (bit addressable) tf1 tr1 tf0 tr0 ie1 it1 ie0 it0 00000000 rw 89 1 tmod timer/counter mode control gate ct m1 m0 gate ct m1 m0 00000000 rw 8a 1 tl0 timer 0 reload l d7 d6 d5 d4 d3 d2 d1 d0 00000000 rw 8b 1 tl1 timer 1 reload l d7 d6 d5 d4 d3 d2 d1 d0 00000000 rw 8c 1 th0 timer 0 reload h d15 d14 d13 d12 d11 d10 d9 d8 00000000 rw 8d 1 th1 timer 1 reload h d15 d14 d13 d12 d11 d10 d9 d8 00000000 rw 8e 1 ckcon [9] clock control x x t2m t1m t0m md2 md1 md0 00000001 rw 8f 1 reserved 90 1 iob [9] port b (bit addressable) d7 d6 d5 d4 d3 d2 d1 d0 xxxxxxxx rw 91 1 exif [9] external interrupt flag(s) ie5 ie4 i2cint usbnt 1 0 0 0 00001000 rw 92 1 mpage [9] upper addr byte of movx using @r0/@r1 a15 a14 a13 a12 a11 a10 a9 a8 00000000 rw 93 5 reserved 98 1 scon0 serial port 0 control (bit addressable) sm0_0 sm1_0 sm2_0 ren_0 tb8_0 rb8_0 ti_0 ri_0 00000000 rw 99 1 sbuf0 serial port 0 data buffer d7 d6 d5 d4 d3 d2 d1 d0 00000000 rw 9a 1 autoptrh1 [9] autopointer 1 address h a15 a14 a13 a12 a11 a10 a9 a8 00000000 rw 9b 1 autoptrl1 [9] autopointer 1 address l a7 a6 a5 a4 a3 a2 a1 a0 00000000 rw 9c 1 reserved 9d 1 autoptrh2 [9] autopointer 2 address h a15 a14 a13 a12 a11 a10 a9 a8 00000000 rw 9e 1 autoptrl2 [9] autopointer 2 address l a7 a6 a5 a4 a3 a2 a1 a0 00000000 rw 9f 1 reserved a0 1 ioc [9] port c (bit addressable) d7 d6 d5 d4 d3 d2 d1 d0 xxxxxxxx rw a1 1 int2clr [9] interrupt 2 clear x x x x x x x x xxxxxxxx w a2 1 int4clr [9] interrupt 4 clear x x x x x x x x xxxxxxxx w a3 5 reserved a8 1 ie interrupt enable (bit addressable) ea es1 et2 es0 et1 ex1 et0 ex0 00000000 rw a9 1 reserved aa 1 ep2468stat [9] endpoint 2,4,6,8 status flags ep8f ep8e ep6f ep6e ep4f ep4e ep2f ep2e 01011010 r ab 1 ep24fifoflgs [9] endpoint 2,4 slave fifo status flags 0 ep4pf ep4ef ep4ff 0 ep2pf ep2ef ep2ff 00100010 r ac 1 ep68fifoflgs [9] endpoint 6,8 slave fifo status flags 0 ep8pf ep8ef ep8ff 0 ep6pf ep6ef ep6ff 01100110 r ad 2 reserved af 1 autoptrset-up [9] autopointer 1&2 setup 0 0 0 0 0 aptr2inc aptr1inc aptren 00000110 rw b0 1 iod [9] port d (bit addressable) d7 d6 d5 d4 d3 d2 d1 d0 xxxxxxxx rw b1 1 ioe [9] port e (not bit addressable) d7 d6 d5 d4 d3 d2 d1 d0 xxxxxxxx rw b2 1 oea [9] port a output enable d7 d6 d5 d4 d3 d2 d1 d0 00000000 rw b3 1 oeb [9] port b output enable d7 d6 d5 d4 d3 d2 d1 d0 00000000 rw b4 1 oec [9] port c output enable d7 d6 d5 d4 d3 d2 d1 d0 00000000 rw b5 1 oed [9] port d output enable d7 d6 d5 d4 d3 d2 d1 d0 00000000 rw b6 1 oee [9] port e output enable d7 d6 d5 d4 d3 d2 d1 d0 00000000 rw b7 1 reserved b8 1 ip interrupt priority (bit ad- dressable) 1 ps1 pt2 ps0 pt1 px1 pt0 px0 10000000 rw b9 1 reserved ba 1 ep01stat [9] endpoint 0&1 status 0 0 0 0 0 ep1inbsy ep1outbs y ep0bsy 00000000 r bb 1 gpiftrig [9, 7] endpoint 2,4,6,8 gpif slave fifo trigger done 0 0 0 0 rw ep1 ep0 10000xxx brrrrbbb bc 1 reserved bd 1 gpifsgldath [9] gpif data h (16-bit mode only) d15 d14 d13 d12 d11 d10 d9 d8 xxxxxxxx rw be 1 gpifsgldatlx [9] gpif data l w/trigger d7 d6 d5 d4 d3 d2 d1 d0 xxxxxxxx rw table 9. nx2lp-flex register summary (continued) hex size name description b7 b6 b5 b4 b3 b2 b1 b0 default access notes 9. sfrs not part of the standard 8051 architecture. 10. if no nand is detected by the sie then the default is 00000000. [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 24 of 33 absolute maximum ratings storage temperature .............. .............. ...... ?65c to +150c ambient temperature with powe r supplied ...... 0c to +70c supply voltage to ground potential ............... ?0.5v to +4.0v dc input voltage to any input pin ........................ +5.25v [11] dc voltage applied to outputs in high z state...... ................... ?0.5v to v cc + 0.5v power dissipation ................... ..................................300 mw static discharge voltage........................................... > 2000v max output current, per i/o port................................. 10 ma operating conditions t a (ambient temperature under bias) ............. 0c to +70c supply voltage............................................+3.00v to +3.60v ground voltage.................................................................. 0v f osc (oscillator or crystal frequency).... 24 mhz 100 ppm (parallel resonant) bf 1 gpifsgldat lnox [9] gpif data l w/no trigger d7 d6 d5 d4 d3 d2 d1 d0 xxxxxxxx r c0 1 scon1 [9] serial port 1 control (bit addressable) sm0_1 sm1_1 sm2_1 ren_1 tb8_1 rb8_1 ti_1 ri_1 00000000 rw c1 1 sbuf1 [9] serial port 1 data buffer d7 d6 d5 d4 d3 d2 d1 d0 00000000 rw c2 6 reserved c8 1 t2con timer/counter 2 control (bit addressable) tf2 exf2 rclk tclk exen2 tr2 ct2 cprl2 00000000 rw c9 1 reserved ca 1 rcap2l capture for timer 2, au- to-reload, up-counter d7 d6 d5 d4 d3 d2 d1 d0 00000000 rw cb 1 rcap2h capture for timer 2, au- to-reload, up-counter d7 d6 d5 d4 d3 d2 d1 d0 00000000 rw cc 1 tl2 timer 2 reload l d7 d6 d5 d4 d3 d2 d1 d0 00000000 rw cd 1 th2 timer 2 reload h d15 d14 d13 d12 d11 d10 d9 d8 00000000 rw ce 2 reserved d0 1 psw program status word (bit addressable) cy ac f0 rs1 rs0 ov f1 p 00000000 rw d1 7 reserved d8 1 eicon [9] external interrupt control smod1 1 eresi resi int6 0 0 0 01000000 rw d9 7 reserved e0 1 acc accumulator (bit address- able) d7 d6 d5 d4 d3 d2 d1 d0 00000000 rw e1 7 reserved e8 1 eie [9] external interrupt en- able(s) 1 1 1 ex6 ex5 ex4 ei2c eusb 11100000 rw e9 7 reserved f0 1 b b (bit addressable) d7 d6 d5 d4 d3 d2 d1 d0 00000000 rw f1 7 reserved f8 1 eip [9] external interrupt priority control 1 1 1 px6 px5 px4 pi2c pusb 11100000 rw f9 7 reserved table 9. nx2lp-flex register summary (continued) hex size name description b7 b6 b5 b4 b3 b2 b1 b0 default access r = read-only bit w = write-only bit b = both read/write bit r = all bits read-only w = all bits write-only note 11. applying power to i/o pins when the chip is not powered is not recommended. [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 25 of 33 dc characteristics usb transceiver usb 2.0-compliant in full- and high-speed modes. ac electrical characteristics usb transceiver usb 2.0-compliant in full- and high-speed modes. table 10.dc characteristics parameter description cond itions min. typ. max. unit v cc supply voltage 3.00 3.3 3.60 v v cc ramp up 0 to 3.3v 200 s v ih input high voltage 2 5.25 v v il input low voltage ?0.5 0.8 v v ih_x crystal input high voltage 2 5.25 v v il_x crystal input low voltage ?0.5 0.8 v i i input leakage current 0< v in < v cc 10 a v oh output voltage high i out = 4 ma 2.4 v v ol output low voltage i out = ?4 ma 0.4 v i oh output current high 4ma i ol output current low 4ma c in input pin capacitance except d+/d? 10 pf d+/d? 15 pf i susp suspend current connected 300 380 [12] a cy7c68034 disconnected 100 150 [12] a suspend current connected 0.5 1.2 [12] ma cy7c68033 disconnected 0.3 1.0 [12] ma i cc supply current 8051 running, connected to usb hs 43 ma 8051 running, connected to usb fs 35 ma i unconfig unconfigured current before bmaxpower granted by host 43 ma t reset reset time after valid power v cc min = 3.0v 5.0 ms pin reset after powered on 200 s note 12. measured at max v cc , 25c. [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 26 of 33 slave fifo asynchronous read figure 11. slave fifo asynchronous read timing diagram [13] slave fifo asynchronous write figure 12. slave fifo asynchronous write timing diagram [13] table 11.slave fifo asynchronous read parameters [15] parameter description min. max. unit t rdpwl slrd pulse width low 50 ns t rdpwh slrd pulse width high 50 ns t xflg slrd to flags output propagation delay 70 ns t xfd slrd to fifo data output propagation delay 15 ns t oeon sloe turn-on to fifo data valid 10.5 ns t oeoff sloe turn-off to fifo data hold 10.5 ns slrd flags t rdpwl t rdpwh sloe t xflg t xfd data t oeon t oeoff n+1 n data t sfd t fdh flags t xfd slwr/slcs# t wrpwh t wrpwl notes 13. dashed lines denote signals with programmable polarity. 14. gpif asynchronous rdy x signals have a minimum setup time of 50 ns when using internal 48-mhz ifclk. 15. slave fifo asynchronous parameter values use internal ifclk setting at 48 mhz. table 12.slave fifo asynchronous write parameters with internally sourced ifclk [15] parameter description min. max. unit t wrpwl slwr pulse low 50 ns t wrpwh slwr pulse high 70 ns t sfd slwr to fifo data setup time 10 ns t fdh fifo data to slwr hold time 10 ns t xfd slwr to flags output propagation delay 70 ns [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 27 of 33 slave fifo asynchronous packet end strobe figure 13. slave fifo asynchronous packet end strobe timing diagram [9] slave fifo output enable figure 14. slave fifo output enable timing diagram [13] slave fifo address to flags/data figure 15. slave fifo address to flags/data timing diagram [13] table 13.slave fifo asynchronous packet end strobe parameters [15] parameter description min. max. unit t pepwl pktend pulse width low 50 ns t pwpwh pktend pulse width high 50 ns t xflg pktend to flags output propagation delay 115 ns table 14.slave fifo output enable parameters parameter description min. max. unit t oeon sloe assert to fifo data output 10.5 ns t oeoff sloe deassert to fifo data hold 10.5 ns table 15.slave fifo address to flags/data parameters parameter description min. max. unit t xflg fifoadr[1:0] to flags outp ut propagation delay 10.7 ns t xfd fifoadr[1:0] to fifodata ou tput propagation delay 14.3 ns flags t xflg pktend t pepwl t pepwh sloe data t oeon t oeoff fifoadr [1.0] data t xflg t xfd flags nn+1 [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 28 of 33 slave fifo asynchronous address figure 16. slave fifo asynchronous address timing diagram [13] sequence diagram sequence diagram of a single and burst asynchronous read figure 17. slave fifo asynchronous read sequence and timing diagram [13] figure 18. slave fifo asynchronous read sequence of events diagram slrd/slwr/pktend slcs/fifoadr [1:0] t sfa t fah table 16.slave fifo asynchronous address parameters [15] parameter description min. max. unit t sfa fifoadr[1:0] to slrd/sl wr/pktend setup time 10 ns t fah rd/wr/pktend to fifoa dr[1:0] hold time 10 ns slrd flags sloe data t rdpwh t rdpwl t oeon t xfd t xflg n data (x) t xfd n+1 t xfd t oeoff n+3 n+2 t oeoff t xflg t sfa t fah fifoadr slcs driven t xfd t oeon t rdpwh t rdpwl t rdpwh t rdpwl t rdpwh t rdpwl t fah t sfa n t=0 t=0 t=1 t=7 t=2 t=3 t=4 t=5 t=6 t=1 t=2 t=3 t=4 nn sloe slrd fifo pointer n+3 fifo data bus not driven driven: x n not driven sloe n n+2 n+3 slrd n n+1 slrd n+1 slrd n+1 n+2 slrd n+2 slrd n+2 n+1 sloe not driven sloe n n+1 n+1 [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 29 of 33 figure 17 diagrams the timing relationship of the slave fifo signals during an asynchronous fifo read. it shows a single read followed by a burst read. ? at t = 0 the fifo address is stable and the slcs signal is asserted. ? at t = 1, sloe is asserted. this results in the data bus being driven. the data that is driven on to the bus is previous data, it data that was in the fi fo from a prior read cycle. ? at t = 2, slrd is asserted. the slrd must meet the minimum active pulse of t rdpwl and minimum de-active pulse width of t rdpwh . if slcs is used then, slcs must be in asserted with slrd or bef ore slrd is asserted (that is the slcs and slrd signals must both be asserted to start a valid read condition). ? the data that will be driven, after asserting slrd, is the updated data from the fifo. this data is valid after a propa- gation delay of t xfd from the activating edge of slrd. in figure 17 , data n is the first valid data read from the fifo. for data to appear on the data bus during the read cycle (that is slrd is asserted), sloe must be in an asserted state. slrd and sloe can also be tied together. the same sequence of events is also shown for a burst read marked with t = 0 through 5. note: in burst read mode, during sloe is assertion, the data bus is in a driven state and outputs the previous data. once slrd is asserted, the data from the fifo is driven on the data bus (s loe must also be asserted) and then the fifo poi nter is incremented. sequence diagram of a single and burst asynchronous write figure 19. slave fifo asynchronous write sequence and timing diagram [13] figure 19 diagrams the timing relationship of the slave fifo write in an asynchronous mode. the diagram shows a single write followed by a burst write of 3 bytes and committing the 4-byte-short packet using pktend. ? at t = 0 the fifo address is applied, insuring that it meets the setup time of t sfa . if slcs is used, it must also be asserted (slcs may be tied low in some applications). ? at t = 1 slwr is asserted. slwr must meet the minimum active pulse of t wrpwl and minimum de-active pulse width of t wrpwh . if the slcs is used, it must be in asserted with slwr or before slwr is asserted. ? at t = 2, data must be present on the bus t sfd before the deasserting edge of slwr. ? at t = 3, deasserting slwr will cause the data to be written from the data bus to the fifo and then increments the fifo pointer. the fifo flag is also updated after t xflg from the deasserting edge of slwr. the same sequence of events are shown for a burst write and is indicated by the timing marks of t = 0 through 5. note: in the burst write mode, once slwr is deasserted, the data is written to the fifo and then the fifo pointer is incremented to the next byte in the fifo. the fifo pointer is post incre- mented. in figure 19 once the four bytes ar e written to the fifo and slwr is deasserted, the short 4-byte packet can be committed to the host using the pktend. the external device should be designed to not assert slwr and the pktend signal at the same time. it should be designed to assert the pktend after slwr is deasserted and met the minimum de-asserted pulse width. the fifoaddr lines are to be held constant during the pktend assertion. pktend slwr flags data t wrpwh t wrpwl t xflg n t sfd n+1 t xflg t sfa t fah fifoadr slcs t wrpwh t wrpwl t wrpwh t wrpwl t wrpwh t wrpwl t fah t sfa t fdh t sfd n+2 t fdh t sfd n+3 t fdh t sfd t fdh t pepwh t pepwl t=0 t=2 t =1 t=3 t=0 t=2 t=1 t=3 t=6 t=9 t=5 t=8 t=4 t=7 [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 30 of 33 ordering information table 17.ordering information ordering code description silicon for battery-powered applications cy7c68034-56lfxc 8x8 mm, 56 qfn ? lead-free silicon for non-battery-powered applications cy7c68033-56lfxc 8x8 mm, 56 qfn ? lead-free development kit CY3686 ez-usb nx2lp-flex development kit package diagram figure 20. 56-lead qfn 8 x 8 mm lf56a 0.80[0.031] 7.70[0.303] 7.90[0.311] a c 1.00[0.039] max. n seating plane n 2 0.18[0.007] 0.50[0.020] 1 1 0.08[0.003] 0.50[0.020] 0.05[0.002] max. 2 (4x) c 0.24[0.009] 0.20[0.008] ref. 0.80[0.031] max. pin1 id 0-12 6.45[0.254] 8.10[0.319] 7.80[0.307] 6.55[0.258] 0.45[0.018] 0.20[0.008] r. 8.10[0.319] 7.90[0.311] 7.80[0.307] 7.70[0.303] dia. 0.28[0.011] 0.30[0.012] 6.55[0.258] 6.45[0.254] 0.60[0.024] n 1 2 top view bottom view side view e-pad (pad size vary by device type) option for cml - bottom view note: dimensions are same with std dwg on upper right except for the u-groove on the paddle .000 1.925 .000 2.375 2.325 r.250 (3x) 2.275 2.175 2.075 1.975 2.225 2.125 r.400 r.300 r.200 r.100 r.600 r.500 r.400 r.300 r.100 r.200 pin #1 id .680 .240typ .680 u-groove dimension e-pad (pad size vary by device type) dimensions in mm[inches] min. max. reference jedec mo-220 51-85144*e [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 31 of 33 pcb layout recommendations [16] the following recommendations should be followed to ensure reliable high-performance operation: ? at least a four-layer impedance controlled boards is recom- mended to maintain signal quality. ? specify impedance targets (ask your board vendor what they can achieve) to meet usb specifications. ? to control impedance, maintain trace widths and trace spacing. ? minimize any stubs to avoid reflected signals. ? connections between the usb connector shell and signal ground must be done near the usb connector. ? bypass/flyback caps on vbus, near connector, are recom- mended. ? dplus and dminus trace leng ths should be kept to within 2 mm of each other in length, with preferred length of 20?30 mm. ? maintain a solid ground plane under the dplus and dminus traces. do not allow the plane to be split under these traces. ? no vias should be placed on the dplus or dminus trace routing unless absolutely necessary. ? isolate the dplus and dminus traces from all other signal traces as much as possible. quad flat package no leads (qfn) package design notes electrical contact of the part to the printed circuit board (pcb) is made by soldering the leads on the bottom surface of the package to the pcb. hence, special attention is required to the heat transfer area below the package to provide a good thermal bond to the circuit board. a copper (cu) fill is to be designed into the pcb as a thermal pad under the package. heat is transferred from the nx2lp-flex to the pcb through the device?s metal paddle on the bottom side of the package. it is then conducted from the pcb?s thermal pad to the inner ground plane by a 5 x 5 array of vias. a via is a plated through hole in the pcb with a finished diameter of 13 mil. the qfn?s metal die paddle must be soldered to the pcb?s thermal pad. solder mask is placed on the board top side over each via to resist solder flow into the via. the mask on the top side also minimizes outgassing during the solder reflow process. for further information on this package design please refer to the application note surface mount assembly of amkor?s microleadframe (mlf) technology . this application note can be downloaded from amkor?s website from the following url: http://www.amkor.com/products/notes_papers/ mlf_appnote_0902.pdf . the application note provides detailed information on board mounting guidelines, soldering flow, rework process, etc. figure 21 below displays a cross-sectional area underneath the package. the cross section is of only one via. the solder paste template needs to be designed to allow at least 50% solder coverage. the thickness of the solder paste template should be 5 mil. it is recommended that ?no clean? type 3 solder paste is used for mounting the part. nitrogen purge is recommended du ring reflow. figure 22 is a plot of the solder mask pattern and figure 23 displays an x-ray image of the assembly (darker areas indicate solder) figure 21. cross-section of the area underneath the qfn package. note 16. source for recommendations: ez-usb fx2?pcb design recommendations , http://www.cypress.com/cfuplo ads/support/app_notes/fx2_pcb.pdf and high speed usb platform design guidelines , http://www.usb.org/developers/docs/hs_usb_pdg_r1_0.pdf. 0.017? dia solder mask cu fill cu fill pcb material pcb material 0.013? dia via hole for thermally connecting the qfn to the circuit board ground plane. this figure only shows the top three layers of the circuit board: top solder, pcb dielectric, and the ground plane. [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 32 of 33 ? cypress semiconductor corporation, 2006. the information contained herein is subject to change without notice. cypress semic onductor corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a cypress product. nor does it convey or imply any license under patent or ot her rights. cypress products are not warranted nor intended to be used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agr eement with cypress. furthermore, cypress does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to re sult in significant injury to the user. the inclusion of cypress products in life-support systems application implies that the manu facturer assumes all risk of such use and in doing so indemni fies cypress against all charges. figure 22. plot of the solder mask (white area) figure 23. x-ray image of the assembly purchase of i 2 c components from cypress, or one of its sublicensed associated companies, conveys a license under the philips i 2 c patent rights to use these components in an i 2 c system, provided t hat the system conforms to the i 2 c standard specification as defined by philips. ez-usb fx2lp, ez-usb fx2 and renume ration are trademarks, and ez-usb is a registered trademark, of cypress semiconductor corporation. a ll product and company names mentioned in this document are the trademarks of their respective holders. [+] feedback [+] feedback
cy7c68033/cy7c68034 document #: 001-04247 rev. *d page 33 of 33 document history page document title: cy7c68033/cy7c 68034 ez-usb nx2lp-flex? flex ible usb nand flash controller document #: 001-04247 rev. *d rev. ecn no. issue date orig. of change description of change ** 388499 see ecn gir preliminary draft *a 394699 see ecn xut minor change: upload data sheet to external website. publicly announcing the parts. no physical changes to document were made *b 400518 see ecn gir took ?preliminary? off the top of all pages. corrected the first bulleted item. corrected figure 3-2 caption. added new logo *c 433952 see ecn rgl added i 2 c functionality *d 498295 see ecn kku updated data sheet format changed in/output refe rence from i/o to io changed set-up to setup changed ifclk and clkout pins to gpio8 and gpio9. removed external ifclk [+] feedback [+] feedback

▲Up To Search▲

Price & Availability of CY3686

	To Download CY3686 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .